TRUCK MANIFOLD ENGINE COVER
Tired of your ulgy oem engine cover? Want to customize your engine bay after a swap? Well we have come up with a cost effective solution just for you! Here is our custom made LS engine cover!
-Fits 99+ truck/tahoe/suburban 4.8, 5.3, 6.0, 6.2 intakes, as well as trail blazer ss intake swaps in an oem vehicle or in a swap. (does not fit 14+ 5.3 or 6.2 truck or suv engines. These are considered gen 5)
-Custom ls engine cover
-CNC cut
-Dimple died
-Bent all in house at our shop special ops motorsports-100% bolt on, all stainless hardware included
-Cover is made out of steel or aluminum
-Both our steel and aluminum covers are ran through our ez-sander for a prior to forming
-Items are shipped raw, we do coat them in a small amount of oil to combat flash rusting while shipping. End user will need to paint or powdercoat the steel ones, the aluminum ones can be installed and left raw if desired.
-Want a matching set of coil covers to finish off your engine bay?
-Click here for our coil cover options!
-Multiple top logos are available seperatley to give your engine bay a one of a kind look!
-Click here for all of our top logos!
-Our classic chevrolet decals are specifically made for our engine covers but look good anywhere!
-Click here for our classic chevrolet decals
*****items ship raw steel or sanded aluminum*****
-(gen 3) this is a 100% bolt on. You just need to determine what options need per your application, read below
The evap system installed from the factory to reduce the evaporative emissions pollution that is produced by the fuel vapors released by the gasoline stored in the fuel tank. This is a key system in an oem vehicle but in a ls swap it is rarely hooked back up. If you choose not to use it we do offer a delete plug to eliminate it! The benefit to doing this on a gen 3 intake set up with our cover is getting the cover to sit lower on the intake. If in an evap solenoid is used you will need to purchase our threaded spacers in order to clear the intact emissions equipment.
-(gen 4) these engines came in trucks, suv and vans from 07-18 in a variety of different sizes 4.8, 5.3, 6.0 and 6.2. The size of the motor does not matter as long as the intake looks like the pictures above. โ
Note*** light duty 1500s came with gen 5 (5.3 and 6.2) engines starting in 2014- current and our gen 4 intake covers do not fit
The evap is located on the drivers side of the intake, above the fuel and will clear the cover no problem. So no evap delete is needed.
-(tbss) these intake swaps are very common because of their 90mm throttle body intake size and hp gains without loosing low end. When ordering a cover for a tbss swap please specify what its going on/in so we can assure you get the correct longer cover if needed. The tbss intake shares the same bolt pattern as a gen 4 intake but needs different spacers to make it sit properly.
-(aluminum mesh) we offer aluminum mesh behind the dimple die holes as an option. This comes with all the stainless hardware and cnc cut mesh sanded to a polished look! When choosing this option we also cnc cut the holes in the exact location for a simple bolt on addition!
-(bends) all covers now receive the nose bent down execpt the tbss cover. The reasoning for this is the spacing from our cover to the throttle body is too close.
Contents include
-engine cover
-metric allen head bolts to fasten to truck intake-billet threaded spacers to clear obstructions on the top of the intake
** free stickers** ๐ค๐
Be sure to follow us on social media- special ops motorsports
**** thanks for supporting small business usa****
INTAKE VERIFICATION
IF YOU ARE UNSURE WHICH INTAKE YOU HAVE, PLEASE REFER TO THE INTAKE PICTURE WITH OUT THE COVER ON IT. PLEASE DONT HESITATE TO ASK US FOR A 100% CONFIRMATION
ALSO CHECK OUT OUR INSTRUCTION PAGE FOR ALL INSTALLATION INSTRUCTIONS